274 pts ยท April 24, 2016
Do your part. Delete your account and downvote Twitter screenshots
If you happen to have Cisco switches you may be able to use TDR to test 24-48 cables at a time.
It's just reversed 12 liters is about 3.17 Gallons
Detroit averages about 1 murder per day
Just FYI in this specific circumstance he looked pretty damn close to the guy they were looking for
If this was single use it's fine. They could also seal it
Between the size of layer lines and the lack of a sealant this might just be a single use high speed print.
Use a repeated food contact rated resin to seal 3d prints for this purpose. This one has not been sealed.
most uncolored PLA is non-toxic but extremely porous and prone to bacterial growth so.. kinda
most PLA is non-toxic, especially non-colored variations. They are not food safe for repeated use due to porosity and difficulty of cleaning
Which wouldn't be as much of an issue if we weren't talking about beer.
I wasn't as concerned about the PLA being toxic as much as porous. Anything that seeped into the pores would breed bacteria.
Definitely my favorite
Welcome to basic training, you have 5 minutes to shit, shower, and shave with 30 other dudes. On the plus side your workout is built in
He might have had a camera on him too but it got covered and they used the audio from that. Idk
That's like, twice a week
I don't mind clover in my lawn but, I can't stand thistle, crabgrass and dandelions.
The World Wide Web one show a man in U.S. military uniform.
www.tor.com/2020/01/03/welcome-to-mystery-flesh-pit-national-park-one-redditors
https://youtu.be/3AryHBXIwXI
You are correct
Almost rolled my ankle on Oscar already
I don't have any copper, but I have a silk orange. I'd guess about $10 + shipping. I'll test out the print on Friday
FlashForge Dreamer and no specific brand I just ordered a bunch of mikada3d silk pla colors
Looks like you your extruder is a bit too hot
I've got something similar, might even match. Mika3d silk green PLA
Anyone want one? Just got a bunch of new filament
That's a lot of PII in one picture
That can't be it, right?
Do your part. Delete your account and downvote Twitter screenshots
If you happen to have Cisco switches you may be able to use TDR to test 24-48 cables at a time.
It's just reversed 12 liters is about 3.17 Gallons
Detroit averages about 1 murder per day
Just FYI in this specific circumstance he looked pretty damn close to the guy they were looking for
If this was single use it's fine. They could also seal it
Between the size of layer lines and the lack of a sealant this might just be a single use high speed print.
Use a repeated food contact rated resin to seal 3d prints for this purpose. This one has not been sealed.
most uncolored PLA is non-toxic but extremely porous and prone to bacterial growth so.. kinda
most PLA is non-toxic, especially non-colored variations. They are not food safe for repeated use due to porosity and difficulty of cleaning
Which wouldn't be as much of an issue if we weren't talking about beer.
I wasn't as concerned about the PLA being toxic as much as porous. Anything that seeped into the pores would breed bacteria.
Definitely my favorite
Welcome to basic training, you have 5 minutes to shit, shower, and shave with 30 other dudes. On the plus side your workout is built in
He might have had a camera on him too but it got covered and they used the audio from that. Idk
That's like, twice a week
I don't mind clover in my lawn but, I can't stand thistle, crabgrass and dandelions.
The World Wide Web one show a man in U.S. military uniform.
www.tor.com/2020/01/03/welcome-to-mystery-flesh-pit-national-park-one-redditors
https://youtu.be/3AryHBXIwXI
You are correct
Almost rolled my ankle on Oscar already
I don't have any copper, but I have a silk orange. I'd guess about $10 + shipping. I'll test out the print on Friday
FlashForge Dreamer and no specific brand I just ordered a bunch of mikada3d silk pla colors
Looks like you your extruder is a bit too hot
I've got something similar, might even match. Mika3d silk green PLA
Anyone want one? Just got a bunch of new filament
That's a lot of PII in one picture
That can't be it, right?